目前濟南GRC構件的技術體系已經成熟，構件建造的建筑物可以達到44層。但是，在我們的生活中，濟南GRC構件還存在著尚未的問題。那么安裝完成后如何去除構件裝飾的味道？

At present, the technical system of GRC components in Jinan is mature, and the building built by components can reach 44 floors. However, in our life, there are still unresolved problems in Jinan GRC components. How to remove the smell of component decoration after installation?

構件裝飾整理去除味道的方法：

Methods for removing odor in the decoration and finishing of components:

1.可以打開窗戶通風。是一種比較簡單實用的構件氣味分散方法。

1. The window can be opened for ventilation. It is a relatively simple and practical component odor dispersion method.

2.房間里堆積著木炭袋、橘子皮等，可以吸收構件的氣味。這種方法起作用的時間有一定的過程。包括綠色植物在內的水果也有助于去除菠蘿蜂蜜等構件的味道。那氣味更香。它可以在室內切菠蘿蜂蜜，在幾天內吸收香味。

2. The room is stacked with charcoal bags, orange peel, etc., which can absorb the smell of components. There is a certain process when this method works. Fruits including green plants also help to remove the taste of components such as pineapple and honey. It smells better. It can cut pineapple honey indoors and absorb the fragrance in a few days.

擴展：構件路安裝注意事項

Extension: component road installation considerations

在安裝前進行現場調查。表面要平整、緊密。如果有多個表面不符合安裝要求，則須進行調整，直到滿足安裝要求為止。其次，進行現場測量，主要根據現場大小和構件進行測量，并進行刻度和標記，以減少施工過程中的誤差。同時繪制相應的圖紙，多方確認后才能使用。

Conduct site investigation before installation. The surface shall be flat and tight. If several surfaces do not meet the installation requirements, they must be adjusted until they meet the installation requirements. Secondly, on-site measurement shall be carried out, mainly according to the size of the site and the components, and calibration and marking shall be carried out to reduce the errors in the construction process. At the same time, corresponding drawings shall be prepared and can be used only after being confirmed by many parties.

在購買構件時，應選擇適當的計算方法。如果安裝過程中出現問題，應及時調整，以免影響后續施工?，F場安裝時，請盡量使用整條線路。如果需要切斷構件，就要用砂紙打磨兩端。

When purchasing components, appropriate calculation methods should be selected. In case of problems during installation, timely adjustment shall be made to avoid affecting subsequent construction. When installing on site, please use the whole line as much as possible. If it is necessary to cut the component, use sandpaper to grind both ends.

構件安裝后，異味不再是必然的。一定要及時通風，加快去除速度，或者在室內放入木炭袋等，吸附氣味。另外，在安裝過程中須注意尺寸測量，避免二次加工帶來的麻煩，希望上述內容能給你的工程帶來一定的便利。更多相關內容就來我們網站http://www.xinyanse.com進行咨詢了解吧！

After the installation of components, peculiar smell is no longer inevitable. Be sure to ventilate in time to speed up the removal, or put charcoal bags indoors to absorb the smell. In addition, pay attention to dimension measurement during installation to avoid the trouble caused by secondary processing. I hope the above contents can bring some convenience to your project. Come to our website for more relevant content http://www.xinyanse.com Consult and understand!