GRC構件是一種裝飾材料，可以以自由的形式滿足設計師各種個性形式的要求，因此受到設計師的青睞，當然，安裝的規格也是必要的，以下廠家將教安裝
濟南GRC構件的正確步驟以及質量標準。
GRC component is a kind of decorative material, which can meet the requirements of various personality forms of designers in a free form, so it is favored by designers. Of course, the installation specifications are also necessary. The following manufacturers will teach the correct steps and quality standards for installing GRC components in Jinan.
安裝GRC構件的正確步驟
Correct steps for installing GRC components
1.根據圖紙在GRC構件安裝處放出定位線。
1. Set out the positioning line at the installation of GRC components according to the drawing.
2.然后按照施工圖紙的說明安裝切割尺寸的GRC構件，切割GRC構件時，如何掌握GRC構件的尺寸，確保線跡的寬度正好。
2. Then install the cut size GRC members according to the instructions of the construction drawings. When cutting GRC members, how to grasp the size of GRC members, first ensure that the width of the stitch is right.
3.粘貼GRC構件時，網眼布可以折疊，也可以直接粘貼。使用性能良好的粘結砂漿，可用薄層密實的方法將砂漿從GRC構件中強制擠出，粘接處用粘接劑固定，寬度小于3mm，保持粘接處牢固清潔。
3. When pasting GRC components, the mesh can be folded or pasted directly. Use the bonding mortar with good performance. The mortar can be forced out of the GRC member by thin layer compaction. The bonding part is fixed with adhesive, with a width of less than 3mm, and the bonding part is kept firm and clean.
4.安裝GRC構件，先測量構件的尺寸，現在試著用平地拼接，構件之間的間隙小于3mm時，用性能良好的粘結砂漿粘結，注意粘結砂漿的均勻分布。
4. When installing GRC components, first measure the size of the components, and then try to splice them with flat ground. When the gap between the components is less than 3mm, use the bonding mortar with good performance to bond, and pay attention to the uniform distribution of the bonding mortar.
5.檢查拼接好的GRC構件，可用砂紙打磨接縫粘結砂漿。粘結砂漿干燥后，可以使用GRC構件的抗裂橡膠進一步粘結。
5. Check the spliced GRC components and polish the joint bonding mortar with sandpaper. After the bonding mortar is dry, the anti-crack rubber of GRC components can be used for further bonding.
GRC構件安裝的質量標準
Quality standard for GRC component installation
1、構件安裝要求橫平豎直，整體在線，圖案完整，曲線光滑，構件表面沒有污染，無缺陷。
1. The components shall be installed horizontally and vertically, with the overall line, complete pattern, smooth curve, and no pollution and defect on the surface of the components.
2、正確找好構件的安裝節點，防止因預埋件錯位導致構件扭曲，長期產生安裝應力和變形。
2. Correctly locate the installation nodes of the components to prevent the distortion of the components due to the misplacement of the embedded parts and long-term installation stress and deformation.
3、構件連接點連接無泄漏，請擰緊螺栓后再擰緊。
3. There is no leakage at the connection point of the component. Please tighten the bolts before tightening.
4、構件接縫光滑，接縫小于10毫米
4. The component joint is smooth, and the joint is less than 10mm
5、縱向構件請勿使上部構件與底部構件重疊，但是，各部件請單獨安裝在墻上。
5. Do not overlap the upper component and the bottom component of the longitudinal component, but install each component separately on the wall.
6、構件安裝后，需要自上而下將表面灰塵、污物清掃干凈，吊鉤間隙應牢固平整。
6. After the installation of components, the surface dust and dirt shall be cleaned from top to bottom, and the hook gap shall be firm and flat.
The above is the installation method and installation quality standard introduced by the manufacturer, which can resist the damage, deformation and cracking of the external environment, and should be operated according to the correct installation method during use; It may endanger personal safety and cause other unnecessary losses. If you need to know more about products, please come to our website http://www.xinyanse.com consulting service
